GE Refrigerator Repair
Aurora, CO
GE Profile, Cafe, and standard model repairs in Aurora. Ice maker, not cooling, water dispenser, control board — same-day service available.
GE has been making refrigerators longer than most companies have existed. They’re solid appliances, well-designed, and parts are usually available. When GE refrigerators come to me in Aurora, it’s usually one of a handful of things: the ice maker, the main control board on Profile models, or a condenser fan failure.
GE also makes the Cafe and Profile lines, which have some electronics-heavy features that require careful diagnosis. I work on all three lines regularly in Aurora.
Why is my GE refrigerator ice maker not working in Aurora?
GE ice makers fail in Aurora for two main reasons. The water inlet valve gets scale buildup from Aurora’s 12–18 GPG hard water, reducing water flow until the ice maker stops producing. Or the ice maker module itself fails — the thermostat inside it trips and doesn’t reset. I carry GE ice maker kits for French door, side-by-side, and top-freezer models.
Common GE Refrigerator Problems I Fix in Aurora
Ice Maker Not Working
GE’s most common issue in Aurora. Either a scaled water inlet valve, a failed ice maker module, or a stuck harvest motor. I diagnose which one before recommending the fix.
Not Cooling Properly
GE cooling failures are usually the evaporator fan, a dirty condenser, or a defrost system failure. Profile models can also have main control board failures that affect cooling. I test components systematically.
Control Board Failure (Profile/Cafe)
GE Profile and Cafe refrigerators have sophisticated control boards. When the board fails, you can get erratic temperature behavior, unresponsive controls, or error codes. Board replacement is $180–$280 plus labor.
Water Dispenser Issues
Aurora’s mineral-rich water (12–18 GPG) clogs GE’s dispenser valve and filter housing over time. I flush the water pathway and replace the inlet valve solenoid if needed.
Refrigerator Making Noise
GE condenser fans on older models can develop bearing failures, causing a rattling or squealing noise. The evaporator fan can also ice over in Aurora’s dry climate and scrape against accumulated frost.
Freezer Not Maintaining Temperature
A GE freezer that runs warm usually has a defrost system failure — heater, thermostat, or timer. I run a forced defrost cycle and test each component to find the failure point.
How much does GE refrigerator repair cost in Aurora?
Most GE repairs run $140–$320 total, including the $75 diagnostic. Ice maker repairs are typically $150–$230. Control board work on Profile/Cafe models runs $220–$340. Compressor issues (less common on GE) run $350–$500. All pricing is flat-rate — I tell you the full cost before I start.
GE Models I Repair in Aurora
- GFE28GYNFS / GFE26JYMFS — French door, ice maker and cooling issues
- GSS25GYPFS / GSE25GSHSS — Side-by-side, water dispenser and ice maker
- PFE28KYNFS (Profile) — French door, control board and twin cooling
- CVE28DP3ND1 (Cafe) — French door, electronic control issues
- GTS22KYNRFS — Top freezer, defrost system failures
GE Profile and Cafe: What’s Different
GE’s Profile and Cafe lines have more electronics than standard GE models. Twin Evaporator Cooling, TwinChill systems, and advanced control boards are great features — but when they fail, diagnosis requires familiarity with GE’s diagnostic modes. I work on Profile and Cafe models regularly and know the failure patterns specific to each line.
Same-Day GE Refrigerator Repair in Aurora
All Aurora ZIP codes covered. $75 diagnostic, flat-rate pricing, 90-day warranty on repairs.
Call (720) 606-7970GE Refrigerator Repair FAQ — Aurora CO
My GE Profile shows an error code on the display — what should I do?
GE Profile error codes usually point to sensor failures (thermistors), fan motor faults, or control board issues. Write down the exact code and call me — I can often pre-diagnose the issue before arriving and bring the right part with me.
Is it worth replacing the control board on an older GE Profile?
Depends on the age of the unit and what else might need work. A GE Profile that’s 8–12 years old with a failed control board is usually worth repairing if that’s the only issue. I’ll give you an honest assessment — sometimes the board is $180 and the fridge has years of life left. Sometimes it makes more sense to replace. I’ll tell you which it is.
Do you repair GE Cafe refrigerators?
Yes — GE Cafe models are technically sophisticated but I work on them regularly. The most common Cafe issue I see in Aurora is the water system (dispenser and ice maker) due to hard water scale buildup.
Can you fix a GE refrigerator that’s leaking water under it?
Yes. Water under a GE refrigerator is almost always a clogged defrost drain, which causes water to pool and drain out the front. I clear the drain tube and clean the drain pan. Usually $100–$150 and done in under an hour.
Do you service GE refrigerators in Aurora’s newer ZIP codes like 80016?
Yes — I cover all of Aurora: 80010, 80011, 80012, 80013, 80014, 80015, 80016, and 80017. No extra travel fee.